A large number of homes (some estimates are up to 60 million homes) are still off-grid, and taking power-lines to these homes may be just too expensive. Many more have long power-cuts and could be categorized as near off-grid.
While decentralized solar at the roof-tops to generate power could be an option for such homes, the costs of a conventional solar PV system to provide basic light and fans (and cell-phone charger) have been high primarily because of (i) poor design, (ii) high AC to DC and DC to AC conversion losses associated with such solar and battery systems and (iii) high costs of batteries.
Solar-DC systems would save about 35-40% of the power as compared to a solar-AC system. Add to it the energy-savings associated with DC appliances, huge gains in efficiency becomes possible. This efficiency gains translate to lower sized solar panel and smaller battery and therefore cost-savings when compared to a solar-AC system. Such a set-up offers an economical and affordable solution for off-grid/ near off-grid homes (homes with large power-cuts), and could also be useful for grid-connected homes in saving power-bills as well as providing back-up power.
This is achieved by Solar-DC Inverterless technology, conceptualized by IIT Madras.IIT Madras has implemented such decentralized Solar-DC systems within IIT Madras and in multiple locations in Tamil Nadu, Andhra Pradesh and Orissa.
It is now working with the Ministry of Power, Rural Electricity Corporation Limited (REC), and state power departments to power about 4000 homes each in Rajasthan and Assam using Solar-DC Inverterless.
From our field trail reports it was inferred that the main obstacle to deployment of solar-DC systems and having DC micro-grids at home today is the unfamiliarity. In order to overcome this, there is a need to innovate and create a market PULL, instead of waiting for the market PUSH.
Uninterrupted DC power
IITM’s UDC (Uninterrupted DC power) Innovation precisely does this. This solution enables homes on the power-grid to get a DC line within home along with the existing AC line, with minimal changes to the power-distribution / transmission system. This DC line which would function even during load-shedding, supplies 48V DC. While, the existing AC line at home would be cut-off during load shedding. Thus a new DC micro-grid is created where the DC power is always ON, but its availability is limited. Homes can now use this DC power-line, if they choose to. This removes the bottleneck of getting DC power at home and will get people to start getting familiar with DC appliances connected to this DC line.
In a nutshell, Solar-DC Inverterless & UDC work hand-in hand to aid homes gradually move towards a more DC world tomorrow.
Solar-DC Inverterless technology, conceptualized and ideated by IIT Madras. This technology uses complete DC solutions to remove AC to DC and DC to AC conversions. Removing the need of conversion helps in saving 30% to 40% of energy. This later provide more power backup with lesser size of batteries and solar panel which thus also contributes in reducing the cost of the system.
The Solar DC products are designed and developed in such a way that it can be easily installed in off-grid or near off-grid homes. These solution can also be seamlessly integrated with the AC power supply providing 24×7 power backup.
With the help of IITM and Ministry of Power, Rural Electricity Corporation Limited(REC) we have completed 4k+ pilot installation in Rajesthan and 7k+ ongoing installations in Assam.
48V DC: THE RIGHT SOLAR DC STANDARDS (Driving Standardization)
DC (direct current) and AC (alternate current) systems were born around the same time in late 1800s and battled head to head in the well-known “War of Currents”. It might have seen that AC has won the power transmission battle, and DC was all washed out, but it wasn’t. Majority of today’s end-use appliances and electronics use DC at various levels of DC voltage. Improvements in power electronics have enabled engineers to develop circuits capable of inexpensively transforming DC voltages.
At the same time, Solar PV which has emerged as a great source of decentralized power produces only DC energy. Batteries which have emerged as a powerful and wide-spread energy storage system can charge/discharge only DC power. When AC power-line is used, AC to DC and DC to AC converters used further increase the power-loss.
All these raises the question, “Why not DC?”
Choice of DC Voltage
It is of utmost importance to carefully consider what should become a standard for various possible voltages between 0 and 60V DC. There are various possible options: 60V, 54V, 48V, 24V, 12V, 5V etc. Let us examine the pros and cons of choosing one of these voltages:
A. Cable losses: a 2.5 sq mm cross-section loop (the commonly used cross-section for AC wiring) would have less than 2% losses for a 48V system, for 12V system, losses would be almost 22%, clearly proving the sub-optimality of reducing voltage below 48V.
B. Cost of wiring: For a given source power output and percentage power loss, the thickness of cable is inversely proportional to the square of source voltage. This implies that compared to a 48 V system, four times the wire thickness and sixteen times the wire thickness are necessary for 24 V and 12 V systems respectively. Cable/wiring costs are directly proportional to the cost of the copper and varies with the size of the wiring.
C. Use of existing inside-building AC wiring: Currently, for inside-building 230V AC wiring, 2.5 sq mm and 4 sq mm are the most widely used cross-sections. For both these cross-sections, a 100W loop on 48V would work with good efficiency as shown above as long as the loop length is moderate. The same does not hold true for 24V or 12V. Thus, using 48V gives us the opportunity to re-use the existing AC wiring loops present inside homes and offices while keeping losses within acceptable limits.
D. Scale of economics: As explained in point c above, for a limited power system, 48V DC and 230V AC loops can use same kind of copper cables. A common design of this kind will enable standardization of cables/wires and give markets an opportunity to exploit economies of scale. This will in turn mean lower cost and ready availability to end customers.
While 48V DC for inside building wiring is being explored for the first time, 48V DC is not uncommon in other fields and well accepted documents exist. A lot of standards related to 48V exist in different fields like Electric Vehicles, Ethernet, Telecom, UPS and Batteries. IEEE802.3af (15.4W/port) and the updated IEEE 802.3at-2009 for Power over Ethernet (PoE) are such widely used standards that are based on 48V. PoE concept is becoming extremely popular as it eliminates the need of a power outlet close to the device. For electric vehicles, leading German carmakers have developed standard LV148 for 48V on-board supply and charging plug owing to the efficiency of 48V network. Other countries like the US have followed it. In field of Telecom, BTS (base transceiver stations) worldwide uses 48V as the primary source of power as the main standard. These standards can be leveraged to learn and create a common platform and align with other areas. Although 48V has been extensively used in some other fields, it was not exploited for electrical purposes till recently, primarily due to two reasons: Affordability and Availability. Integrated circuits, LED and BLDC revolution have addressed both of these limitations.
Availability of Appliances
A wiring standard is of importance and use only if the compatible equipment exists. Hence, an obvious question is whether 48V DC appliances exist. Answer is a resounding yes. There exist a wide range of low power appliances that work on 48V. Full size BLDC fans of around 30W power rating and 48V input requirement are being produced by TVS Lucas and Crompton Greaves and are readily available. 48V LED tube-lights and bulbs also exist. Electronics use variable voltages and have internal conversions. 19V and 5V are two commonly used voltages. 48V is higher than both and hence, can be easily deployed with simple high-efficiency DC-DC convertors. 48V to 19V or 5V DC-DC conversion is much more efficient than existing 230V to 19V or 5V AC-DC conversion being deployed in case of mobiles, laptops, televisions etc. Speakers, webcams, sensors and a lot of other electronics can also work very easily on 48V.One important aspect to note is that wiring losses become large when larger currents are used. For example, if currents are of the order of 10A (500W power consumption for 48V DC voltage), the wires need to be thicker. Higher power appliances like air-conditioners, mixers, electric-stoves shall use more than 500W and 48V DC may not be appropriate for this. 380V DC could be a good candidate for such higher power consuming appliances. The current standard being presented is focused on 48V LVDC wiring for inside-buildings with an upper limit of 10A on the current. The proposal of IEEE LVDC committee can be a starting point for defining the standard. The standard addresses all important aspects required for a fool-proof deployment.
Deploying a DC power-line inside the building and using it to directly power these DC appliances and devices will ensure energy savings in two ways: Use of higher efficiency DC devices and elimination of conversion losses.
Safety While 60V DC in itself is safe, even the smallest variation in the voltage could take it to unsafe levels. Up to 15% variation in voltage is common for any system in practice. The standard voltage needs to be chosen such that despite any fluctuation on the positive side, the SELV limit of 60 V DC is not exceeded. Same holds true for 54V: 15% variation would make it exceed the 60V SELV limit. These considerations leave 48V as the highest voltage level where even with the 15% voltage fluctuation the devices can operate without posing any safety risks. The peak voltage shall not exceed 55V which is well within SELV limit. Even a 48V battery never needs voltage in excess of 57V to charge. So while 48V DC would be the highest safe voltage, use of 24V, 12V or 5V DC would be equally safe.
The discussion on “Why 48V DC” has centered around five major areas: reliability, availability of appliances, efficiency and safety. More emphasis is being placed upon utilizing alternate sources of renewable energy. Solar power is the primary focus as these elements can be deployed almost anywhere in the world. Solar panels produce power at a DC voltage. This has traditionally been converted to AC in order to be integrated into the existing power system. On a 48V DC distribution system, a direct connection can be made with these sources to the DC appliances that operate at 48V DC making them more efficient and easier to use. With many industries lined up to manufacture such appliances, the definite sustainable advantage of a 48VDC system is thus seen.
Why Solar DC
- Low Cost – Save up to 50% upfront cost as compared to regular AC solution.
- Save Money – Save up to 50% on your monthly electricity bills.
- Less Space – Takes half the space as compared to AC solar solution.
- Safe – No worry from electric shock as the DC appliances are safer than 230V AC appliances.
- Reliable – DC Appliances have higher reliability and gives far better life as compared to AC appliances.
- Efficient – Removing multiple conversions helps in reducing power losses by 30 to 40 percent.